Test task: tension-/compression tests at metals with increased temperature
Maschine: testing machine Inspekt 100 kN +550mm with 2. upper testing space 100kN
Accessories: Furnace changing device for 3 high temperature furnaces, motorized high temperature extensometer, following sample holder and extensive accessories for adaptation warm course linkage and high temperature pressure device
Software: Labmaster with metall tension test, compression test, block program, Print to Word, additional software SteadyRise for controlling and computing of high temperature furnices, costum special program for forse-/tension-/temperature calibration, data export function
Branch of trade: Manufacturer of glass reinforced plastics pipe systems
Test task: tension-/pressure- and bending tests at GFK-pipes
Machine: testing machine Inspekt 100kN with lateral testing space 50kN for pressure- and bending tests
Accessories: hydraulic clamping fixtures 100kN for flat test pieces with a width of 60mm, pressure plates for determination of the ring rigidity, bending device
The stacked Polystyrene samples will be added on the feeding conveyer (2200mm) and from there they will be conveyed to a 900 mm of height magazine to get isolated. In addition the data of the lowest sample are recorded by a bar code reader and transferred to the data base of the testing software. The recorded height of the sample will be used for the separation of samples. The unloaded sample is pushed by a linear drive onto a available scale (customer). After the weighting the samples will be moved by a linear drive to the test bench. With the recorded data from the bar-code-reader, the testing machine ist adjusted for directly conducting of pressure or bending tests. Testet Polystyrene samples will be disposed by compressed air and collected in a waste container behind the testing machine. A manual operation of the test equipment is possible without changes at the automation plant.
tension-/ compression tests on plastics and construction units at increased temperature
Machine:
testing machine Inspekt table 10 kN
Accessories:
heating chamber with temperatur range from –40°C up to 260°C, tension- and compression device
Software:
Lab master with plastic traction test, compression test, block program, auxiliary software SteadyRise for control and monitoring of climatic/temperature chambers, data export function
Semiautomatic traction tests on construction units for 100% examination
Machine:
testing machine Inspekt mini 3 kN
Characteristics:
Testing machine for load tests of pins devices for practical fixation of fireing pins with electro-pneumatic sample marking and pneumatic sample ejection. The device was designed for considering time-optimized sample changes as well as precision and durability of the test tools.
The rehearse-affecting wearing parts are economically exchangeable. To avoid an overstressing of the test pieces during the sample marking, a evenly pneumatic pressing of the marking stamp with a highest level of 1kN will be applied.
Software:
Lab master with metal traction test, special block program for automated test sequences
Technological testing of abrasion and sliding qualities
Device for the technological examination of abrasion and sliding qualities
Branch of trade:
steel industry
Test task:
technological examination of abrasion and sliding qualities of steelplates with pressure forces up to 50kN and departure speeds up to 1000 mm/min
Machine:
testing machine 500 kN
Characteristics:
Load/ downholder strength 800N-50kN, digitally regulated load strength and additional collection of the working actual strength with a power analyzer as measuring channel.
This can be connected by an optional analogue input directly with the test equipment control. The input of the being strength takes place at the display of the device control.
It exists also the possibility to start a constant load rate over a digital I/O (-24V level) synchronously with the traction test in the device control.
The exchangeable "holding down borders " will be fastened in the device by clamps and can be heatet up to 100°C. Test distance per course maximally 250mm - maximum allowable strength with the device 100kN
Software:
Lab master with metal traction test, plastic traction test, bending test, compression test and the module video recording
Tension tests at ambient temperature and in a temperature chamber with metals and plastics
Machine:
Testing machine Inspekt 100 kN +550mm with lateral testing space 50kN
Accessories:
temperature chamber –80°C up to 300°C,
relocatable on a roller carriage, wedge screwing holding fixtures, shears holding fixtures for plastic samples, pressure plates, bending bank for testing in the temperature chamber with inductive way tracer, video extensometer
Software:
Labmaster with metal tension test, plastics tension tests, bending tests, pressure tests and with video recording modul
tension test of artificial biomaterials (crucial ligaments) with simulation of natural environment (blood)
Maschine:
tension-pressure testing machine inspekt 10 kN
Accessories:
horizontal tempering bath RT - 40°C with thermostat control; use of salt solutions possible
Characteristics:
horizontal tensile test in salt bath; machine can be converted for standard tensile tests without much effort (removal of tempering bath from testing space)
Software:
Hegewald & Peschke Ltd. universal material testing software, tension- compression testing of plastics
Contact-free sagging measurement of construction materials at 1,600 °C by video extensometer
Software
Hegewald & Peschke Ltd. universal material testing software, bending test
Universal Testing Machine
inspekt desk10 kN
Packaging and foil industry
Test task:
90 ° peeling (drawing-off) test of splicing tape, roll peeling test of adhesive plaster, measurement of static friction of textiles or splicing tape acc. to DIN 53375
