Branch of trade:

Insulation industry

Test task:

tension-/pressure- and bending tests on Polystyrene samples

Machine:

testing machine Inspekt table 5kN with automated supply system

Characteristics:

The stacked Polystyrene samples will be added on the feeding conveyer (2200mm) and from there they will be conveyed to a 900 mm of height magazine to get isolated. In addition the data of the lowest sample are recorded by a bar code reader and transferred to the data base of the testing software. The recorded height of the sample will be used for the separation of samples. The unloaded sample is pushed by a linear drive onto a available scale (customer). After the weighting the samples will be moved by a linear drive to the test bench. With the recorded data from the bar-code-reader, the testing machine ist adjusted for directly conducting of pressure or bending tests. Testet Polystyrene samples will be disposed by compressed air and collected in a waste container behind the testing machine. A manual operation of the test equipment is possible without changes at the automation plant.

Software:

Labmaster with module for automated supply system and robot control.

Sample movie:

Branch of trade:

automobile component supplier

Test task:

tension-/pressure- and bending tests on ceramic samples and construction units

Machine:

testing machine Inspekt table 50kN

Accessories:

3-/4-point-bending device 1kN for ceramic with integrated bending thrue measuring system, 1kHz-method

Software:

Labmaster with traction test, compression test, block program, data acquisition frequency 1kHz, data export function

Branch of trade:

automobile component supplier

Test task:

tension-/ compression tests on plastics and construction units at increased temperature

Machine:

testing machine Inspekt table 10 kN

Accessories:

heating chamber with temperatur range from –40°C up to 260°C, tension- and compression device

Software:

Lab master with plastic traction test, compression test, block program, auxiliary software SteadyRise for control and monitoring of climatic/temperature chambers, data export function

Branch of trade:

aircraft industry

Test task:

Semiautomatic traction tests on construction units for 100% examination

Machine:

testing machine Inspekt mini 3 kN

Characteristics:

Testing machine for load tests of pins devices for practical fixation of fireing pins with electro-pneumatic sample marking and pneumatic sample ejection. The device was designed for considering time-optimized sample changes as well as precision and durability of the test tools.

The rehearse-affecting wearing parts are economically exchangeable. To avoid an overstressing of the test pieces during the sample marking, a evenly pneumatic pressing of the marking stamp with a highest level of 1kN will be applied.

Software:

Labmaster with metal traction test, special block program for automated test sequences

Sample movie:

Branch of trade:

steel industry

Test task:

technological examination of abrasion and sliding qualities of steelplates with pressure forces up to 50kN and departure speeds up to 1000 mm/min

Machine:

testing machine 500 kN

Characteristics:

Load/ downholder strength 800N-50kN, digitally regulated load strength and additional collection of the working actual strength with a power analyzer as measuring channel.

This can be connected by an optional analogue input directly with the test equipment control. The input of the being strength takes place at the display of the device control.

It exists also the possibility to start a constant load rate over a digital I/O (-24V level) synchronously with the traction test in the device control.
The exchangeable "holding down borders " will be fastened in the device by clamps and can be heatet up to 100°C. Test distance per course maximally 250mm - maximum allowable strength with the device 100kN

Software:

Labmaster with metal traction test, plastic traction test, bending test, compression test and the module video recording

Branche:

Higher technical institute in Andorf / Austria

Test task:

Tension tests at ambient temperature and in a temperature chamber with metals and plastics

Machine:

Testing machine Inspekt 100 kN +550mm with lateral testing space 50kN

Accessories:

temperature chamber –80°C up to 300°C,
relocatable on a roller carriage, wedge screwing holding fixtures, shears holding fixtures for plastic samples, pressure plates, bending bank for testing in the temperature chamber with inductive way tracer, video extensometer

Software:

Labmaster with metal tension test, plastics tension tests, bending tests, pressure tests and with video recording modul

branch of trade:

steel industry

Test task:

warm tension test

Machine:

testing machine Inspekt 250 kN

Accessories:

2 furnaces with a temperature up to 900°C, movable over roller guide, high temperature- extensometer, parallel closing hydraulic clamps, fully automated extension sensors for standard tension tests.
This solution realises for users, to change the samples inside the extended kiln when you heat up the new samples inside the second or third kiln again. Thereby there will be a significant decrease of testing time.

Software:

Labmaster with metal tension test and the kiln regulator.

branch of trade:

automobile industy

Test task:

tension-, pressure- and bending tests on automobil- parts and classical material testing

Machine:

testing machine inspekt 250 kN/special

Accessories:

span for fixing of car seats and other parts

Characteristics:

lateral, opened test space for tests of larger components

branch of trade:

steel industry

Test task:

tension-, pressure- and bending tests on pipes for the automobile industry

Machine:

testing machine inspekt 300 kN/special

Accessories:

hydraulic fixtures for metal tension tests and protective casing for the whole system

Characteristics:

lateral bending bench for the bending tests up to 150kN on pipes

branch of trade: 

automobile component supplier

Test task:

tension-, pressure- and bending tests on standard samples and components of the automobile industry

Machine:

testing machine Inspekt 400 kN, with solid protective casing

Accessories:

wedge clamping accessories 400kN, compression device and bending bench

Software:

Labmaster

Test task:

Fracture toughness values KIC in tension and bending test

Machine:

resistance testing machine inspekt 400 kN, minimum speed 10 µm/ min, roll thread spindle drive

Accessories:

Nitrogen cold chamber - 150 ° C- +250 ° C

Software:

Software for KIC tension and bending tests acc. to ASTM E399

Test task:

Fracturing force of safety belt - tightener - buckle combination

Machine:

Testing machine inspekt 100 kN, extended to 500 mm

Accessories:

Front and back safety doors

Characteristics:

Baffle protection for dampening of impact of metal parts

Software:

Hegewald & Peschke Ltd. universal material testing software, tension- compression testing of components

Test task:

DIN EN 1607 bending test, tensile test of insulating materials

Machine:

Universal testing machine inspekt 20 kN, testing space widened to 650 mm

Accessories:

Special bending bench for samples of 2,000 mm length and up to 500 mm width

Software:

Hegewald & Peschke Ltd. universal material testing software, bending test of insulating materials

Test task:

tension test of artificial biomaterials (crucial ligaments) with simulation of natural environment (blood)

Machine:

tension-pressure testing machine inspekt 10 kN

Accessories:

horizontal tempering bath RT - 40°C with thermostat control; use of salt solutions possible

Characteristics:

horizontal tensile test in salt bath; machine can be converted for standard tensile tests without much effort (removal of tempering bath from testing space)

Software:

Hegewald & Peschke Ltd. universal material testing software, tension- compression testing of plastics

Test task:

DIN EN 10002 metal tensile test, measurement of hot yield strength

Machine:

Universal testing machine inspekt 250 kN, longer testing space

Accessories:

foldable 3-zone furnace up to 900°C, temperature measurement at 3 sample positions, furnace control by sample surface temperature, elongation measurement directly on the sample by sensor finger up to 1,500 °C

Software

Hegewald & Peschke Ltd. universal material testing software, metal tensile test acc. to DIN EN 10002

Test task:

Longitudinal elongation and transversal contraction of plastics samples at various temperatures and humidities

Machine:

Universal testing machine inspekt 50 kN

Accessories:

Mechanical contact extensometers for longitudinal and transversal elongation measurement

Characteristics:

Climate chambers with controlled humidity and temperature ranges

Software

Hegewald & Peschke Ltd. universal material testing software, tension-compression testing of components

Test task:

High-temperature bending strength and sagging of magnesite bricks at 1,600 °C

Machine:

Compression-bending testing machine inspekt 50 kN

Accessories:

High temperature furnace up to 1,600 °C; video extensometer

Characteristics:

Contact-free sagging measurement of construction materials at 1,600 °C by video extensometer

Software

Hegewald & Peschke Ltd. universal material testing software, bending test

Test task:

90 ° peeling (drawing-off) test of splicing tape, roll peeling test of adhesive plaster, measurement of static friction of textiles or splicing tape acc. to DIN 53375

Machine:

Testing machine inspekt 10 kN

Accessories:

mobile peeling table on roll guide elements, moved by arm to guarantee exact vertical force induction

Software:

Hegewald & Peschke Ltd. universal material testing software, peeling test