Logo
 
 
 
Testing machine for torsion tests

Torsion testing device

Torsion testing machine Inspekt T-500H

With the torsion tester Inspekt T-500H a maximum torque of 500Nm at a rotational speed of 25 turns per minute can be realized.

Automated hardness tester for car and truck rims

Automated hardness tester for car and truck rims

Brinell hardness testing (HBT) according to DIN EN ISO 6506

The hardness tester for rims is an electromechanic special hardness tester, that is specialised for rim testing. The test frame divides in samples table, guidance device with load device followed from the test head.

Torsion testing device Inspekt T200H

Torsion testing device

Torsion testing machine inspekt T-200H

With the Inspekt T-200H torsion tester, a maximum torque of 200Nm can be achieved at a rotational speed of up to 60 turns per minute.

Device for torsion testing

Device for torsion testing

Rotary module device 800Nm

Rotary module device 800Nm for forming friction tests.

Rotational impact tester for impact tests

Rotational impact tester

The rotational impact tester is used for impact tests. These highly dynamic tensile tests with a long linear test path are applied, for example, in the testing of fibre composites and technical textiles.

Impact testing on car radiators

Stone impact tester

Test stand for stone impact tests

This stone chip tester can be used to test large components in particular, such as car radiators.

The test stand is tightly clad on all sides and can be opened from two sides. The firing device can only be operated when the door is closed. 

Automated hardness testing system

Automated hardness testing system with robot

The hardness testing station has a modular design and, according to requirements, can be supplemented by sample processing stations or additional test systems (e.g. geometric measurement or determination of the surface roughness). This means motor blocks, steel or aluminum rims and even housing parts can be tested. 

 

Test stand for component tests for the automotive industry

Test stand for cable-controlled gearshift

The test stand is intended for vertical and horizontal testing of cable pulls for gearshifts.

The test software LabMaster from Hegewald & Peschke allows complete control of the machine, display of measured data, calculation of test results and data storage.

Cam shaft test bench

Crank shaft test bench

Crank shaft test bench

Hegewald & Peschke Meß- und Prüftechnik GmbH has provided automotive suppliers with further hardness testing systems for determining the surface hardness of automotive crank shafts and cam shafts.

Rockwell Hardness Test Bench for crankshafts

Automatic Hardness Testing on crankshafts

This hardness test bench for crankshafts is a especially for this case constructed machine using a Rockwell- testing head. Clamping and unclamping as well as the positioning of the test piece are manually operated. The positioning as well as the clamping of the test gripper (with hardness test head) happens motorised due to operating the corresponding controls and sensors.

Hardness testing equipment for crankshafts

Automotives - hardness testing

Hardness testing equipment for crankshafts

The Rockwell hardness testing equipment for crankshafts is a device designed particularly for this application purpose using a Rockwell measuring head of the company ERNST.

Testing of clutch springs for commercial vehicles

Testing on disc springs

Universal testing machine inspekt 100kN

For this application the universal testing machine Inspekt 100kN is used as a clutch spring testing machine. For this purpose it is equipped with a suitable testing device for disc springs. 

Universal testing machine inspekt S-L 250kN

Universal shaft testing in the automotive industry

Universal testing machine inspekt S-L 250kN in horizontal configuration

  • branch: automotive industry

Automotive universal shafts and drive trains are subject to considerable compressive and tensile mechanical loading during use...

Testing gas springs with universal testing machine inspekt solo 1 kN

Gas spring testing

Universal testing machine inspekt solo-L 1 kN

Universal testing machine inspekt solo 1 kN in L-design with increased testing speed of 3000mm/min for testing gas pressure dampers.

Test rig for car seats

Test rig for car seats

Test rig for vertical und horizontal test of car seats. 1 electromechanical actuator, without loading pads, including force sensor. Test procedure supported by comprehensive software.

Shear test on brake pads

Determination of the shear strength of brake linings

Universal testing machine Inspekt table 250 kN

  • Branch: automotive industry

With this universal testing machine Inspekt table 250 kN brake linings can be tested for shear strength. For this purpose, this testing machine has been equipped with a shearing device, a hydraulic unit and an industrial safety door...

 

Universal testing machine inspekt 100kN

Tensile tests on the components of vehicle seats

Universal testing machine inspekt 100kN, extended by 550mm, with an external load cell

  • Branch: automotive engineering

To reduce the risk of injury in automobile accidents, especially safety relevant components of vehicle seats are tested using the inspekt 100kN special testing machine in terms of their material quality and stability... 
 

Universal testing machine inspekt mini 3kN with a special mounting device

Testing Equipment for the determination of adhesion forces

Universal testing machine inspekt mini 3kN

  • Branch: automotive engineering

A modern automobile is made up of up to 10,000 individual components, including numerous small and micro components. The Inspekt mini 3kN universal testing machine enables tensile and pressure tests on especially sensitive and sometimes heavily stressed small components like side windows at cars with an inspection fixture for detention force determination of splicing tapes...

Universal testing machine inspekt 100kN, extended

Fracturing force of the safety belt, safety belt tightener and safety belt buckle combination

Universal testing machine inspekt 100kN, extended version

  • Branche: automotive industry

The inspekt 100kN universal testing machine determines the fracturing force of the safety belt, safety belt tightener and safety belt buckle combination with a nominal load of up to 100kN... 

 

Search by industry and material


Are you looking for a specific standard or another testing solution? Willy recommends the full text search.

 

Safe test results:
certifications