Wire testing machine
Reverse bend testing machine 180° for wire samples
The facility is used for bending fatigue tests according to DIN 51211 and ISO7801 on wires with diameters of 0.3 - 10.0mm. The wire samples are bent with a 90° angle to the left and to the right...
Device for shock tests
Device for impact tests according to EN 61730-2
This machine allows shock tests for solar modules according to the standard EN 61730-2. The modules have to be fixed vertically on a transport trolley, which has been equipped with an appropriate support for fixation on the frame of the testing device.
Friction test stand
Friction test stand for examination of pin - cylinder pairs under climate influence
This test stand is used for examining cylinder – pin pairs in the range of sparse wear. The total wear is limited to 2.5 mm of which 1.5 mm.
Mechanical creep behaviour testing equipment
Mechanical creep behaviour testing equipment for leather samples
Load test stand with 5 load stations, respective maximum permissible load 200N by applying of maximally 4 50N-plates, enterprise by pneumatic circuit.
Fully-automated metal tensile test
Automated testing system with universal testing machine and robot
The automated test centre from Hegewald & Peschke offers high test speeds, operator-independent evaluation and automatic recording of test results. The core of the system is a universal testing machine of the type Inspekt...
Stone impact tester
Test stand for stone impact tests
This stone chip tester can be used to test large components in particular, such as car radiators.
The test stand is tightly clad on all sides and can be opened from two sides. The firing device can only be operated when the door is closed.
Automated test cell for metal tensile tests
Universal testing machine inspekt 250 kN with robot
This automated test cell for tensile tests on reinforcing steel and wire specimens consists of a 250kN universal testing machine with hydraulic fixtures from Hegewald & Peschke, a robot, a specimen recognition station, a sample rack and a scrap container. The cross-section determination during the tensile test is carried out by means of a scale and a length measuring system...
Automated hardness testing system with robot
The hardness testing station has a modular design and, according to requirements, can be supplemented by sample processing stations or additional test systems (e.g. geometric measurement or determination of the surface roughness). This means motor blocks, steel or aluminum rims and even housing parts can be tested.
Test stand for cable-controlled gearshift
The test stand is intended for vertical and horizontal testing of cable pulls for gearshifts.
The test software LabMaster from Hegewald & Peschke allows complete control of the machine, display of measured data, calculation of test results and data storage.
Crank shaft test bench
Crank shaft test bench
Hegewald & Peschke Meß- und Prüftechnik GmbH has provided automotive suppliers with further hardness testing systems for determining the surface hardness of automotive crank shafts and cam shafts.
Bending devices and folding devices
Flexure test kits for 3- and 4-point bending tests and folding tests
Applications for bending devices and folding devices:
- Determination of material properties of brittle composites, ceramics, metals, wooden panels, rigid plastics
- Analysis of welded sheets
1D LENGTH MEASUREMENT DEVICE "HEAVY"
very robust linear measure gadget made of steel for profiles with large cross section, on mobile frame
- measuring length: 3200 mm
- for cross sections up to 300 x 300 mm
- accuracy: ± (0,05 mm + 0,02 mm x L), L=measuring length in m
1D LENGTH MEASUREMENT DEVICE "HEAVY"
very robust digital measuring device made of steel for rod-shaped workpieces, tubes, profiles, rods, bars, material-cuts…
- measuring length: 1250 mm, 1600 mm, 2200 mm
- accuracy standard: ± (0,05 mm + 0,02 mm x L), L=measuring length in m
- accuracy enhanced (option): ± (0,02 mm + 0,01 mm x L), L=measuring length in m
1D LENGTH CONTROL DEVICE FOR TAPE MEASURES
control and calibration device for long tape measures
- measuring length: 20,000 mm (others on request)
- accuracy: ± (0,05 mm + 0,01 mm x L), L=measuring length in m
- microscope or video monitor with crosshair
High temperature furnaces
Material testing up to 1600°C
The further development of high temperature materials, as used in the construction of turbines or boilers for power stations or for aircraft engines, is a central focus of material research.
Rockwell-Hardness tester HP 150 R
HP 150 R - The Rockwell specialist
The Rockwell Hardness Tester HP 150 R is suitable for hardness tests in the range from 0.2 kg to 250 kg.
Fully-automated metal tensile test
Automated testing system with universal testing machine and robot
The automated test centre from Hegewald & Peschke offers high test speeds, operator-independent evaluation and automatic recording of test results. The core of the system is a universal testing machine of the type Inspekt...
Bending test on ceramic according to ASTM C674
Universal testing machine inspekt solo 2,5 kN
3-point bending tests with measuring probe according to ASTM C674 to characterize the properties of the ceramics both before and after the firing process
Test rig for child bicycle seats according to DIN EN 14344
Test equipment for stability and fatigue testing
The test rig is suitable for stability testing and fatigue testing of child bicycle seats according to DIN EN 14344.
The testing machine is conveniently operated via a PLC control with touch screen, on which the test parameters and the status of the test can be read in real time.
Temperature chambers & climate chambers
Temperature & climate chambers - warmer, colder, moisture
Temperature and climate chambers provide the possibility of material and component testing under defined environmental conditions...
Rockwell Hardness Test Bench for crankshafts
Automatic Hardness Testing on crankshafts
This hardness test bench for crankshafts is a especially for this case constructed machine using a Rockwell- testing head. Clamping and unclamping as well as the positioning of the test piece are manually operated. The positioning as well as the clamping of the test gripper (with hardness test head) happens motorised due to operating the corresponding controls and sensors.
Test rig for arm rests
Test rig for arm rest testing - Calmar one
- test rig for alternating bending tests of arm rests according to EN 1335, EN 1728, EN 581-2,
DIN 4551, BIFMA X5.1 and BSI/BS 5459 - basic test frame with electromotive height adjustment of the main traverse
- can be equipped with 2 strength-regulated or strength-regulated and road-regulated actuators (pneumatic test axes), 2 load cells
Weights
Weight disks for furniture stability tests
- aluminium weight disks acc. to EN with 350 mm diameter, 48 mm height and 10 kg weight for furniture stability tests
- steel weight disks, 5 / 10 kg, with ball grips and 32 mm bore, as additional weights used among others as seat weights
Portal drop test rig
Portal drop test rig for seating furniture, tables, upholstery, beds - Calmar one
- testing of chairs, stools, tables, beds acc. to BIFMA X5.1, BIFMA X6.1, EN 581-2, EN747-2, EN 1728, EN 1730, ISO 7173, EN 12520, EN 14072
- PLC controller "Calmar I"; number of cycles and cycle time can be set arbitrarily
- moveable testing portal for carrying a drop tester
Universal testing machine inspekt table
Material testing machines up to 250 kN
The testing machine series inspekt table was developed for standard-compliant materials and component testing in the medium load range, with particular attention paid to reliability and flexibility. It is ideally suited for materials testing of plastics or non-ferrous metals as well as for testing smaller components, for example from instrument engineering. Inspekt table is available in six different load levels from 5 kN to 250 kN. On request, the testing machines of the inspekt table series can be equipped with a second test area. They are available as floor-standing or table-top versions, depending on the requirements of the workplace.
Automotives - hardness testing
Hardness testing equipment for crankshafts
The Rockwell hardness testing equipment for crankshafts is a device designed particularly for this application purpose using a Rockwell measuring head of the company ERNST.
Pendulum stroke accessories
For pendulum stroke tests
- pendulum stroke hammer 2kg, 5kg or 6,5kg for pendulum stroke tests
Stability testing table
Test bench for determining the stability of chairs
Test table for determining the stability of seating furniture such as chairs, swivel chairs, stools, armchairs, cantilever chairs in accordance with the standards EN 1022, EN 1729-2, EN 581-2, ISO 7174-2 and BIFMA X5.1
Tilting drop test rig - Calmar one
Test rig for tilting drop tests at chairs - Calmar one
- Performance of tilt-fall tests on chairs according to DIN 68878/1
- SPS-controlled test bench
- automatic switch-off in case of fracture of the test specimen
- Various chair types can be clamped on the base plate using sliding brackets
Optical Extensometers - Video extensometer
Deformation measurement by video extensometer
Non-contact deformation measuring device for material testing on the basis of high-resolution video technology using the surface structure or, if required, markings.
Portal drop test rig
Portal drop test rig for seating furniture, tables, upholstery, beds - Calmar one
- testing of chairs, stools, tables, beds acc. to BIFMA X5.1, BIFMA X6.1, EN 581-2, EN747-2, EN 1728, EN 1730, ISO 7173, EN 12520, EN 14072
- PLC controller "Calmar I"; number of cycles and cycle time can be set arbitrarily
- moveable testing portal for carrying a drop tester
Universal testing machine inspekt
Material testing machines 100 kN to 2.500 kN
The series inspekt fulfils highest demands in terms of measurement accuracy and versatility. It allows tensile, compression, bending or torsion tests, flexibly adapted to customers test conditions. It is also characterised by its first-class frame stiffness, modern control electronics, and a convincing cost/performance ratio. The size of the test rooms of the individual machines can be customized. It is also possible to add one or more test room. Thus, the top-quality, rugged machines can be used for almost any testing task at the best reliability and accuracy.
Shear frame testing system
for textile semi-finished products and composites
Test system for testing the tensile load of textiles and textile-reinforced plastics (e.g. composites, prepregs or organic sheets) with different types of bond...
Universal testing machine inspekt micro S500N
Material testing machines up to 500N
Static micro testing system with spindle drive for tensile testing, compression testing, peel testing and bending testing of micro components, as two-column testing system or testing system in C-frame construction...
Extensometers
From manual to fully automated - extensometers for material testing
Manual clip-on extensometers for fine extension measurement (E-modulus, Rp) or long-distance extensometers for fine and coarse extension measurement (E-modulus, Rp, A)...
Hardness Tester for Jominy-Testing
Automated Hardness Tester AT200 for Jominy-Testings at up to 6 samples
This hardness tester for evaluation of Jominy-tests is an automated system composed of the following described components:
Software HardWin XL
Hardness Testing Evaluation Software
Software HardWin XL Standard
- designed for Windows XP/Vista
- PC Software or Brinell, Vickers, Rockwell, Knoop tests
- suitable for routine tests
Double test rig
Double test rig for alternating bending tests on seating furniture and upholstery - Calmar pro
- testing of seat, back and arm rests, and side to side testing according to EN 1335, EN 581-2-3, EN 1728, DIN 68878, BIFMA X5.1
- basic test frame with crosshead, that is height-adjustable by electric motor
- can be equipped with 4 load-controlled or load- and position-controlled pneumatic test axes with 4 load cells 5kN
Long-term test stand
Test stand for long-term tests on drawers, drawer guidings and functional fittings
- tests according to EN 15338, EN 1727 und DIN 68898
- tests with the pneumatic test axis can be carried out load- or position-controlled
- stroke up to 800 mm, test speed up to 0.3 m/s test load up to 1500N
Testing the shear forces of contact elements
Universal testing machine inspekt table blue 20 kN with shear device
Shear tests are used to determine whether the solder contacts between the switching contact and the component can withstand the high stresses to which they are subjected in practice, often with many millions of switching cycles. For this purpose, the component to be tested is clamped in a specially developed shearing device and subjected to a steadily increasing shearing force until the switching contact shears off.
Universal testing machines inspekt H-HF
Servo-hydraulic material testing machines up to 1000kN
The servo-hydraulic universal testing machines of the series inspekt H-HF have been designed for routine jobs in metalworking and building materials industries. They are equipped with a mechanical wedge type grip for round and flat specimens. Optionally, Hegewald & Peschke MPT GmbH offers a load frame with a user-friendly, hydraulic clamping tool. Furthermore, two test spaces allow for tensile, pressure, and bending tests without changeover times, which guarantees a high test throughput.
Optical extensometers - Laser extensometer
Deformation measurement with the laser extensometer
The non-contact linear expansion measurement allows the automatic determination of the initial gauge length (L0). The optical system does not influence the measurement with knife edges or its own weight. Laser and video extensometers are used.
Calibration machine for three load cells
Testing machine 10 kN and 50 kN for calibration purposes
Universal testing machine inspekt table 10 kN or inspekt table 50 kN as calibration machine, equipped with three load cells. The testing machine is designed for testing and calibrating load cells in different force ranges.
Swivel test rig
Swivel tests on seating furniture and furniture casters - Calmar one or Calmar pro
- testing of casters, x-bases, substructures and gas springs on seating furniture according to DIN 4551, EN1335, NEN 1812 and BIFMA X5.1
- equipped with 1 load-controlled pneumatic test axis, load cell 5kN and 1 electromotive rotation axis test
- loads up to 2500 N
Horizontal impact testing
Horizontal shock testing device (basketball test)
- stability testing of seating furniture, tables, stools and drawer units according to BS 4875-8 and EN 13150
- testing device is a horizontal shock testing device (basketball), which is blown up to a pressure of 73.5 +/- 5kPa and hangs on flexible wire ropes with a length of 850mm
Loading pads
Loading pads for longtime furniture testing
Loading pads are all equipped with an adapter for the 20 mm clamp system and a Cardan joint to decouple the load cell from bending moments
Standard types:
- loading pad round, 100 mm diameter
- loading pad round, 200 mm diameter
- seat dummies acc. to DIN/EN and NEN, GFK or polyamide full material ram rectangular, 250x200 mm (EN), GFK or polyamide full material...
Testing of electrical switches and buttons
Universal testing machine inspekt table blue 5 kN
By means of special devices it is possible to check the amount of force and path for actuating and releasing the buttons and for actuating the switches.
Kontakt:
Hegewald & Peschke
Meß- und Prüftechnik GmbH
Am Gründchen 1
01683 Nossen
Telefon: +49 35242 445-0
Fax: +49 35242 445-111
E-Mail: info@hegewald-peschke.de
Internet: www.hegewald-peschke.de
Austausch von Branchenwissen:
Sichere Prüfresultate:
